Mill Machines

Used Mill Equipment

There are many different names that are used to describe particle size reduction: milling, grinding, granulating, comminuting, etc. Milling systems can size reduce wet or dry powders. Their are variable speed drives that permit low speed screening and high speed impacting with one milling system. A typical milling system consists of an inlet chamber with a rotor screen and an outlet. The particle size depends upon the speed of the rotor, rotor type, screen hole size and the feed rate of the product. High shear granulation turns powders into dense granules for tableting or coating. Powders are added to a mixing bowl. A large impeller spins the powders into a vortex. A chopper tool shears the granules and removes the air. The granulated product is dried in the mixing bowl or fluid bed dryer.
Contact Us

再保险lated Categories

Mill Equipment In Stock

Fitzpatrick Mill Chilsonator IR520

Photo of Fitzpatrick Mill Chilsonator IR520
Thumbnail of Fitzpatrick Mill Chilsonator IR520 Thumbnail of Fitzpatrick Mill Chilsonator IR520 Thumbnail of Fitzpatrick Mill Chilsonator IR520 Thumbnail of Fitzpatrick Mill Chilsonator IR520 Thumbnail of Fitzpatrick Mill Chilsonator IR520

Fitzpatrick Mill Chilsonator IR520

  • Manufacturer:Fitzpatrick
  • Model Number:IR520
  • Frain Number:5H7500

菲茨帕特里克模型IR520, 316不锈钢,滚er compactor, chilsonator rated up to 150kg of product per hour – depending on materials, application, machine configuration and environment being run in. (2) screw feed design has 13" long x 9" wide x 10" deep ID stainless steel product hopper with rotary product assit feeder to 3" OD x 12" long horizontal screw that eliminates vacuum dearation to 2" OD x 18" long vertical pre-compression screw that compresses product for more uniformity prior to feeding into the 5cm x 20cm or 2" wide x 8" OD groved product compaction rollers with roller force of 26 KN/CM and roller gaps of 1mm to 6mm, powered by 5 Hp motor drive with noise level rating of 75 DB. Remote control panel has A/B controller with parker panel view touch pad controls, A/B vari-speed controllers and e-stop. Mounted on (4) stainless steel legs with casters.

OAD: 48" L x 45" W x 70" H Chilsonator
48" L x 32" W x 60" H Control Panel

Get a Free Quote Call:630-629-9900

Fitzmill Mill Hammer DAS06

Photo of Fitzmill Mill Hammer DAS06
Thumbnail of Fitzmill Mill Hammer DAS06 Thumbnail of Fitzmill Mill Hammer DAS06 Thumbnail of Fitzmill Mill Hammer DAS06 Thumbnail of Fitzmill Mill Hammer DAS06 Thumbnail of Fitzmill Mill Hammer DAS06

Fitzmill Mill Hammer DAS06

  • Manufacturer:Fitzmill
  • Model Number:DAS06
  • Frain Number:R32890

Fitzmill Model DAS06, 316 stainless steel, sanitary, with enclosed, pressurized chamber, particle reduction, hammer mill with pounds of product per hour – depending on materials and application. Equipped with 15" long x 15" wide x 12" deep product hopper with safety grid and 4" OD x 12" long single auger feed screw powered by 3 Hp motor drive, 6" x 11" feed throat with (16) fixed, reversible stainless steel, blunt / knife blades driven by 10 Hp motor drive and has a 14" long x 7" wide product discharge port with safety grid and 30" floor clearence. Control panel has mill and feed screw start, stop push buttons with feed screw speed control dial, amp guage and e-stop, enclosed pressure control regulator with power on / off, safe pressure and alarm indicator with high, low and safe pressure guage. Mounted on (4) leg stainless steel frame with locking casters.
用于精密磨削和particl控制e size reduction in pharmaceutical processing and other sanitary industries.

OAD: 69" L x 50" W x 55" H

Get a Free Quote Call:630-629-9900

Quadro Mill Hammer 194S

Photo of Quadro Mill Hammer 194S
Thumbnail of Quadro Mill Hammer 194S Thumbnail of Quadro Mill Hammer 194S Thumbnail of Quadro Mill Hammer 194S Thumbnail of Quadro Mill Hammer 194S Thumbnail of Quadro Mill Hammer 194S

Quadro Mill Hammer 194S

  • Manufacturer:Quadro
  • Model Number:194S
  • Frain Number:5H7501

Quadro Model 194S, 316 stainless steel particle size reduction Comil. Rated from 1,800 to 4,000 lbs of product per hour – depending on materials and application. Equipped with 5¾" diameter feed throat, 8" diameter screen and 6" diameter discharge port with 21" ground clearance. Control panel with push button start / stop. Mounted on stainless steel (4) leg frame with casters.

OAD: 40"L x 32"W x 50"H

Get a Free Quote Call:630-629-9900

Mikron / Hosokawa Mill Hammer SCB

Photo of Mikron / Hosokawa Mill Hammer SCB
Thumbnail of Mikron / Hosokawa Mill Hammer SCB Thumbnail of Mikron / Hosokawa Mill Hammer SCB Thumbnail of Mikron / Hosokawa Mill Hammer SCB Thumbnail of Mikron / Hosokawa Mill Hammer SCB Thumbnail of Mikron / Hosokawa Mill Hammer SCB

Mikron / Hosokawa Mill Hammer SCB

Mikron, Mikro Pulverizer, Model SCB ,stainless steel hammer mill with production rates per hour – depending on materials and application. Equipped with 16" wide x 16" long x 12" deep feed hopper, (2) 3" OD feed augers and (12) sets of 6" wide swinging blunt impact hammers powered by 10 Hp motor drive and has product discharge with 56” floor clearance. Mounted on (4) leg mild steel base frame. Used to grind, de-lump, pulverize and process wet / dry products.

OAD: 50" L x 42" W x 78" H

Get a Free Quote Call:630-629-9900

Fryma Mill Colloid MZ-110

Photo of Fryma Mill Colloid MZ-110
Thumbnail of Fryma Mill Colloid MZ-110 Thumbnail of Fryma Mill Colloid MZ-110 Thumbnail of Fryma Mill Colloid MZ-110 Thumbnail of Fryma Mill Colloid MZ-110 Thumbnail of Fryma Mill Colloid MZ-110

Fryma Mill Colloid MZ-110

  • Manufacturer:Fryma
  • Model Number:MZ-110
  • Frain Number:5H6390

Fryma Model MZ110, stainless steel, Colloid mill with production rates from 300 to 3000 Litres of product per hour – depending on materials and application. Equipped with 17-1/4" ID x 21" Deep stainless steel, connical product hopper with 6" OD rotor / stator and 3" ID and 2-1/2" OD sanitary side ports, base motor drive. Mounted on 26" x 18" stainless steel base with casters. Mill is mainly used for the wet milling of liquid to highly viscous products, if necessary with different milling sets. They are used primarily in the chemical industry as well as in food production.

OAD: 26" L x 18" W x 49" H

Get a Free Quote Call:630-629-9900

Rietz Mill Hammer RA3-12-K122

Photo of Rietz Mill Hammer RA3-12-K122
Thumbnail of Rietz Mill Hammer RA3-12-K122 Thumbnail of Rietz Mill Hammer RA3-12-K122 Thumbnail of Rietz Mill Hammer RA3-12-K122 Thumbnail of Rietz Mill Hammer RA3-12-K122 Thumbnail of Rietz Mill Hammer RA3-12-K122

Rietz Mill Hammer RA3-12-K122

  • Manufacturer:Rietz
  • Model Number:RA3-12-K122
  • Frain Number:5H6437

Rietz Model RA3-12-K122, versatile, variable speed 45 degree angle disintegrator with pounds of product per hour – depending on materials and application. Equipped with 24" OD reduction chamber and has (5) sets of 3 impellers 12" OD stacked on top of each othe rwith 24" OD cover and 360 degree reduction screen (change part per application) which is held between the housing cradle and has clamp down access door with attached product funnel and 4" OD product port. Belt driven rear mounted 50 Hp motor drive with safety guarding and e-stop. 18" OD x 18" funnel style discharge with 4" floor clearence (with funnel) and 43" discharge height (without funnel). Mounted on heavy duty (4) leg frame with leveling screws.
Used for high-speed shredding and wet grinding of fibrous and other tough materials, also used for fine pulping dispersing and homogenizing.

OAD: 94" L x 50" W x 70" H

Get a Free Quote Call:630-629-9900

Rietz Mill Hammer RA312K122

Photo of Rietz Mill Hammer RA312K122
Thumbnail of Rietz Mill Hammer RA312K122 Thumbnail of Rietz Mill Hammer RA312K122 Thumbnail of Rietz Mill Hammer RA312K122 Thumbnail of Rietz Mill Hammer RA312K122 Thumbnail of Rietz Mill Hammer RA312K122

Rietz Mill Hammer RA312K122

  • Manufacturer:Rietz
  • Model Number:RA312K122
  • Frain Number:5H6436

Rietz Model RA3-12-K122, versatile, variable speed 45 degree angle disintegrator with pounds of product per hour – depending on materials and application. Equipped with 24" OD reduction chamber and has (5) sets of 3 impellers 12" OD stacked on top of each othe rwith 24" OD cover and 360 degree reduction screen (change part per application) which is held between the housing cradle and has clamp down access door with attached product funnel and 4" OD product port. Belt driven rear mounted 75 Hp motor drive with safety guarding and e-stop. 18" OD x 18" funnel style discharge with 4" floor clearence (with funnel) and 43" discharge height (without funnel). Mounted on heavy duty (4) leg frame with leveling screws.
Used for high-speed shredding and wet grinding of fibrous and other tough materials, also used for fine pulping dispersing and homogenizing.

OAD: 94" L x 50" W x 70" H

Get a Free Quote Call:630-629-9900

Fryma Mill Colloid MZ80

Photo of Fryma Mill Colloid MZ80
Thumbnail of Fryma Mill Colloid MZ80 Thumbnail of Fryma Mill Colloid MZ80 Thumbnail of Fryma Mill Colloid MZ80 Thumbnail of Fryma Mill Colloid MZ80 Thumbnail of Fryma Mill Colloid MZ80

Fryma Mill Colloid MZ80

  • Manufacturer:Fryma
  • Model Number:MZ80
  • Frain Number:5H6301

Fryma, Model MZ-80, stainless steel, toothed colloid mill with production rates from 100 to 1000 liters of product per hour – depending on materials and application. Equipped with 12½" OD x 11" Deep stainless steel connical product hopper, 2" OD / 1½"ID tri-Clamp discharge and 3 Hp motor drive. Mounted on 24" x 17" stainless steel base with casters.
Mill is capable of running in both batch operation with hopper or in continuous in-line processing system without the hopper. Used for homoginizing, dispersing, refining emulsifing liquid to highly vicous products such as mustard, creams, mayonnaise, peanut butter, omitments, toothpastes as well as household and chemical products.

OAD: 46"L x 17"W x 41"H

Get a Free Quote Call:630-629-9900

Fitzmill Mill Hammer DKASO12

Photo of Fitzmill Mill Hammer DKASO12
Thumbnail of Fitzmill Mill Hammer DKASO12 Thumbnail of Fitzmill Mill Hammer DKASO12 Thumbnail of Fitzmill Mill Hammer DKASO12 Thumbnail of Fitzmill Mill Hammer DKASO12 Thumbnail of Fitzmill Mill Hammer DKASO12

Fitzmill Mill Hammer DKASO12

  • Manufacturer:Fitzmill
  • Model Number:DKASO12
  • Frain Number:R31950

Fitzmill, Model DKAS012, stainless steel, hammer mill with pounds of product per hour – depending on materials and application. Stainless steel contact parts. Equipped with 22" long x 16" wide x 5" deep feed pan and 12" x 12" feed throat with (32) fixed impact blades and 14" x 16" discharge port with safety grid and 42" ground clearance Control panel has start, stop, e-stop push button controls and 20 Hp motor drive. Mounted on (4) leg frame with casters.

OAD: 48" L x 38" W x 68" H

Get a Free Quote Call:630-629-9900

Fryma Mill Colloid MZ80A

Photo of Fryma Mill Colloid MZ80A
Thumbnail of Fryma Mill Colloid MZ80A Thumbnail of Fryma Mill Colloid MZ80A Thumbnail of Fryma Mill Colloid MZ80A Thumbnail of Fryma Mill Colloid MZ80A Thumbnail of Fryma Mill Colloid MZ80A

Fryma Mill Colloid MZ80A

  • Manufacturer:Fryma
  • Model Number:MZ80A
  • Frain Number:R31830

Fryma, Model MZ-80/A, stainless steel, toothed colloid mill with production rates from 100 to 1000 liters of product per hour – depending on materials and application. Equipped with 12½" OD x 11" Deep stainless steel connical product hopper, 2" OD discharge, jacketed milling chamber and 3 Hp motor drive. Mounted on 24" x 24" stainless steel base with casters.
Mill is capable of running in both batch operation with hopper or in continuous in-line processing system without the hopper. Used for homoginizing, dispersing, refining emulsifing liquid to highly vicous products such as mustard, creams, mayonnaise, peanut butter, omitments, toothpastes as well as household and chemical products.

OAD: 24"L x 24"W x 40"H

Get a Free Quote Call:630-629-9900

Fitzmill Mill Hammer DAS06

Photo of Fitzmill Mill Hammer DAS06
Thumbnail of Fitzmill Mill Hammer DAS06 Thumbnail of Fitzmill Mill Hammer DAS06 Thumbnail of Fitzmill Mill Hammer DAS06 Thumbnail of Fitzmill Mill Hammer DAS06 Thumbnail of Fitzmill Mill Hammer DAS06

Fitzmill Mill Hammer DAS06

  • Manufacturer:Fitzmill
  • Model Number:DAS06
  • Frain Number:R31740

Fitzmill, Model DASO6, stainless steel hammer mill with production rates per hour – depending on materials, application and machine configuration. Equipped with 24" long x 16" wide x 4" deep feed pan and 6" x 6" feed throat with (16) fixed knife / impact blades powered by 7.5 Hp motor drive. 15” long x 6” wide product discharge with 32” floor clearance. Control panel has start, stop, reset push button controls. Mounted on (4) leg stainless steel frame.

OAD: 60" L x 36" W x 60" H Without Casters
68" H With Casters

Get a Free Quote Call:630-629-9900

Fitzpatrick Mill Hammer DKAS012

Photo of Fitzpatrick Mill Hammer DKAS012
Thumbnail of Fitzpatrick Mill Hammer DKAS012 Thumbnail of Fitzpatrick Mill Hammer DKAS012 Thumbnail of Fitzpatrick Mill Hammer DKAS012 Thumbnail of Fitzpatrick Mill Hammer DKAS012 Thumbnail of Fitzpatrick Mill Hammer DKAS012

Fitzpatrick Mill Hammer DKAS012

  • Manufacturer:Fitzpatrick
  • Model Number:DKAS012
  • Frain Number:R31742

Fitzmill, Model DKAS012, stainless steel hammer mill with pounds of product per hour – depending on materials, application and machine configuration. Equipped with 5-3/4" OD product port and 12" x 12" feed throat with (32) fixed knife / Impact blades powered by 20 Hp motor drive, bottom 10" ID product discharge port with 24” floor clearance. Control panel has start, stop push buttons and hand held controller. Mounted on (4) leg stainless steel legs with casters. Used to grind, de-lump, pulverize and process wet or dry products.

OAD: 60" L x 60" W x 78" H With Casters
58" H Without Casters

Get a Free Quote Call:630-629-9900
1 2 3 4 5 6 … 12